BOOT LOOP RESTART: HOW TO FIX IT
Question: i Unlocked for my Mobily 4G LTE Router , but it is not working,it rebooting continuously
This question is asked, here is the answer to it:
Answer: You are in BOOT LOOP, it means the device is not listening to any orders and keeps on trying to update itself which it fails and keeps restarting.. People say it can not be fixed.. No its not like that, there is a will, there is a way..
It can be easily fixed even by a guy who is non tech at all. Just follow the steps carefully and not to break anything. Again i want to emphasize that this will be at your own risk, any damage happens we are not responsible at all. Do at your own risk.
However to ease you, we did it at first attempt with zero to little knowledge about technology stuff ;)
STEP 1: Things you need:
STEP 2:
Open the 2 screw at the back of router
Now to tell you that this cover has 4 hard rubber locks, you can just try to open them and you will hear click on each corner of router.
Separate back cover
Now you can see CHIP BOARD itself
It Also has 2 screws
Open them up as shown in picture
STEP 3:
Most important and careful step
Now identify GSM PORT, it has IMEI written over it.
Its rectangular shaped chip that has 2 screws at its end as shown in picture below
Open these 2 screws
Now carefully pull out GSM PORT, it should be separated easily with a gentle pull
STEP 4: Connect to power cable to router and start it
It should be working now
Keep GSM port separated and of course without sim in sim port
STEP 5: Follow the same steps to unlock device as shown in following link
After you unlocked device with all steps in the above post without missing any point.
follow this step
STEP 6: Connect GSM Port
Connect GSM port to its place where it was as shown above
Put SIM card in sim port
Restart Router
Check for the connection , signal strength and SIM PORT LIGHT
If showing NO SIM
Confirm if the SIM PORT light is showing 'on' as shown in the above picture ...
If no, remove GSM PORT and insert it in again carefully and push a bit that its fixed inside well.
STEP 7: Confirmation
Check all system and internet is working before closing back router..
Everything should be working just fine..
THE END: ENJOY
Hopefully you solved your problem yourself with our blog, Keep visiting us. Any problem in the steps, comment down in comment box and leave your question or problem.. We will get back to you with solution as soon as possible. It would be better if you upload picture of the problem where you got stuck with. So we can help you from the same point, in order to not to waste your precious time..
Question: i Unlocked for my Mobily 4G LTE Router , but it is not working,it rebooting continuously
This question is asked, here is the answer to it:
Answer: You are in BOOT LOOP, it means the device is not listening to any orders and keeps on trying to update itself which it fails and keeps restarting.. People say it can not be fixed.. No its not like that, there is a will, there is a way..
It can be easily fixed even by a guy who is non tech at all. Just follow the steps carefully and not to break anything. Again i want to emphasize that this will be at your own risk, any damage happens we are not responsible at all. Do at your own risk.
However to ease you, we did it at first attempt with zero to little knowledge about technology stuff ;)
STEP 1: Things you need:
- Mobily QDC ROUTER
- Screw driver (Star Shapped)
- Time required 30 min to 1 hour
STEP 2:
Open the 2 screw at the back of router
Now to tell you that this cover has 4 hard rubber locks, you can just try to open them and you will hear click on each corner of router.
Separate back cover
Now you can see CHIP BOARD itself
It Also has 2 screws
Open them up as shown in picture
STEP 3:
Most important and careful step
Now identify GSM PORT, it has IMEI written over it.
Its rectangular shaped chip that has 2 screws at its end as shown in picture below
Open these 2 screws
Now carefully pull out GSM PORT, it should be separated easily with a gentle pull
STEP 4: Connect to power cable to router and start it
It should be working now
Keep GSM port separated and of course without sim in sim port
How to unlock mobily 4G LTE router QDC in one attempt 2016
After you unlocked device with all steps in the above post without missing any point.
follow this step
STEP 6: Connect GSM Port
Connect GSM port to its place where it was as shown above
Put SIM card in sim port
Restart Router
Check for the connection , signal strength and SIM PORT LIGHT
If showing NO SIM
Confirm if the SIM PORT light is showing 'on' as shown in the above picture ...
If no, remove GSM PORT and insert it in again carefully and push a bit that its fixed inside well.
STEP 7: Confirmation
Check all system and internet is working before closing back router..
Everything should be working just fine..
THE END: ENJOY
Hopefully you solved your problem yourself with our blog, Keep visiting us. Any problem in the steps, comment down in comment box and leave your question or problem.. We will get back to you with solution as soon as possible. It would be better if you upload picture of the problem where you got stuck with. So we can help you from the same point, in order to not to waste your precious time..
Hi, thanks for your hard work, I unlocked my QDC router. But the problem is it work for 10 minutes and restart the connection (I am using Zain postpaid data sim in it). Is it problem with router or with the connection.
ReplyDeleteDear Juliet,
DeleteI would advise you to restart the software process and the last step is to revert it back to stable version that works for all sin cards . Follow the previous post and the last 2 steps. Hope it helps.
Still any problems.. msg here and I will update u in detail.
hi it was unlocked but the router getting restarts again and again(Looping) I HAVE REMOVED THE GSM PORT AND DID ALL INSTRUCTION BUT IT WAS RESTART happening
ReplyDeleteWhich version of software is it showing now???
ReplyDeleteOne most Imp step to stop reboot looping is shown in the post below... How to unlock mobily 4G LTE router QDC in one attempt 2016.
There r 2 version of softwares, one is quite unstable n keeps on updating itself. 2ND version is stable...
Also in the setting u have to uncheck the server to 0.00.00.0
See the previous post on how to unlock qdc, it will help.
Still any problem. Comment back. And I will write it in more detail.
Dear Sir, I have already unlocked my modem before two month but now its not connecting and not showing the home page also. still its light is blinking only..i think its firmware is out of date...pls do needful Thanks
ReplyDeleteDear Anees,
DeleteSame happen to me also; if you got some information let us know......
Dear anees,
ReplyDeleteI succeeded; try from first, and leave the modem in ON condition some more time. automatically page will appear, go by step by step
great .good to know @MALFA and @anees...
ReplyDeleteall we need is go step by step from both posts and it will be fixed for sure...
any more help..im here :)
I follow the instructions,but when i open it,the internet lights keeps on blinking,what should i do?
ReplyDeleteOk you have reached the 2nd step.. Please follow step 3 carefully and remove the 2 screws of GSM Port..
DeleteNow carefully pull out GSM PORT, it should be separated easily with a gentle pull
After step 3 when u go to step 4 it will show you all lights and few blinking..(thats normal)
From here on you have to follow the link to update the device by software but keep the device open as it is.. DOnt connect back GSM port unless u unlock the device.
Please follow this link to unlock device http://www.howtofate.tk/2016/05/how-to-unlock-mobily-4g-lte-router-qdc.html
then follow step 6 and it should be working..
Success in 1 attempt is to follow each and every step carefully and dont miss a single line or step.
Hope it helps
I do it all
ReplyDeleteAnd gsm port
All lamps on other date
hi my mobily 4g router model :-QDC yesterday firmware updated and sim working ok but morning on my router but not working blinking only on/off light and signal light blink some times only plz advice how to rectify problem.
ReplyDeleteyour router is again in loop restart mode probably, i advise u to restart the process of unlocking again and don't forget to change the update ip to 00.00.00.0
DeleteHope it helps
This comment has been removed by the author.
ReplyDeleteI made firmware update to my QDC router .the first step but I could not continue because the router does not open it's ip page 192.168.2.1 what is the problem .can anybody help.
ReplyDeleteTry IP 192.168.1.1
DeleteHi. My router power light is blinking, becomes stable and blinking continuously. So, I followed the steps as mentioned above to resolve Restart Boot Loop. I step 6, after connecting GSM port, the same problem persists. Only power light is blinking, stable and blinking again. Please help to resolve this issue. Thanks.
ReplyDeleteHi Kumar,
DeleteI will suggest u to downgrade software after installing the usual one. Then it will not behave like this. Some routers don't support the first software , however after downgrade it will work just fine.
Do update me about the progress.
hi am facing issue too.
ReplyDeletei made firmware update but it is continously blinking..lte and on/off button please help
This comment has been removed by the author.
Deleteplease i need to change the power ic .. need to know the ic code or number to change it
ReplyDeletehi..thanks for this tutorial..before my router was restarting continuously but after following all steps my router started working..but now i have only one problem..after 3-4 min of connection stage the router restarts again..i have done all steps including step 9..kindly help
ReplyDeletethanks
ReplyDeletei did all step
but router still on/off loop
Yes ,this advise is working 100% , first remove GSM port , connect your router , reset first , then update with the older version , disable SIM security e.t.c , then flash LTE module file , then start the router without SIM .flash the latest version of software , here we go router is working again.warning do all these flashing process while you removed your GSM port.
ReplyDeleteTyuii
ReplyDeleteDid you hear there's a 12 word sentence you can say to your man... that will induce intense emotions of love and instinctual appeal to you buried inside his heart?
ReplyDeleteBecause hidden in these 12 words is a "secret signal" that triggers a man's instinct to love, admire and guard you with his entire heart...
12 Words That Fuel A Man's Love Instinct
This instinct is so hardwired into a man's mind that it will drive him to try better than before to to be the best lover he can be.
As a matter of fact, triggering this all-powerful instinct is so mandatory to having the best ever relationship with your man that the instance you send your man one of these "Secret Signals"...
...You will instantly find him expose his mind and heart for you in a way he's never expressed before and he'll distinguish you as the one and only woman in the world who has ever truly understood him.
If you're attempting to lose pounds then you absolutely have to try this brand new custom keto diet.
ReplyDeleteTo create this service, licensed nutritionists, personal trainers, and cooks joined together to produce keto meal plans that are productive, convenient, money-efficient, and enjoyable.
Since their first launch in early 2019, 1000's of individuals have already completely transformed their body and well-being with the benefits a certified keto diet can offer.
Speaking of benefits: in this link, you'll discover 8 scientifically-certified ones given by the keto diet.
Hi my router not working and light only on last three lights and not respond to any reset and not appear connected on laptop help me please
ReplyDeletei love you bro... you save my router. its working now
ReplyDeleteEven after removing the gsm module its still looping! What to do?
ReplyDelete