Restart BOOT LOOP after attempting to unlock mobily 4G LTE router QDC

BOOT LOOP RESTART: HOW TO FIX IT

Question: i Unlocked for my Mobily 4G LTE Router , but it is not working,it rebooting continuously

This question is asked, here is the answer to it:

Answer: You are in BOOT LOOP, it means the device is not listening to any orders and keeps on trying to update itself which it fails and keeps restarting.. People say it can not be fixed.. No its not like that, there is a will, there is a way..

It can be easily fixed even by a guy who is non tech at all. Just follow the steps carefully and not to break anything. Again i want to emphasize that this will be at your own risk, any damage happens we are not responsible at all. Do at your own risk.
However to ease you, we did it at first attempt with zero to little knowledge about technology stuff ;)

STEP 1: Things you need:

1. Mobily QDC ROUTER
2. Screw driver (Star Shapped)
3. Time required 30 min to 1 hour

STEP 2:

Open the 2 screw at the back of router

Now to tell you that this cover has 4 hard rubber locks, you can just try to open them and you will hear click on each corner of router.

Separate back cover

Now you can see CHIP BOARD itself

It Also has 2 screws

Open them up as shown in picture

STEP 3:

Most important and careful step

Now identify GSM PORT, it has IMEI written over it.

Its rectangular shaped chip that has 2 screws at its end as shown in picture below

Open these 2 screws

Now carefully pull out GSM PORT, it should be separated easily with a gentle pull


STEP 4: Connect to power cable to router and start it

It should be working now

Keep GSM port separated and of course without sim in sim port

STEP 5: Follow the same steps to unlock device as shown in following link

How to unlock mobily 4G LTE router QDC in one attempt 2016

After you unlocked device with all steps in the above post without missing any point.
follow this step

STEP 6: Connect GSM Port

Connect GSM port to its place where it was as shown above

Put SIM card in sim port

Restart Router

Check for the connection , signal strength and SIM PORT LIGHT

If showing NO SIM

Confirm if the SIM PORT light is showing 'on' as shown in the above picture ...

If no, remove GSM PORT and insert it in again carefully and push a bit that its fixed inside well.

STEP 7: Confirmation

Check all system and internet is working before closing back router..

Everything should be working just fine..


THE END: ENJOY

Hopefully you solved your problem yourself with our blog, Keep visiting us. Any problem in the steps, comment down in comment box and leave your question or problem.. We will get back to you with solution as soon as possible. It would be better if you upload picture of the problem where you got stuck with. So we can help you from the same point, in order to not to waste your precious time..

APN settings for Saudi Arabia network providers: UNLOCKED 4G LTE routers QDC QUANTA

Settings:

Here are the settings, leave everything else as it is in picture,

Just you need to change APN according to your network sim

FOR STC:

APN:  jawalnet.com.sa

FOR ZAIN

APN: zain

FOR MOBILY itself ;) really you need this APN, ok here it is

APN: web2

 IF you don't like to change APN settings every time you use different network provider sim, simply leave this portion Blank and change 'Always Connected' to 'Auto Network triggered' and Apply Changes.

It should work fine without changing APN settings with every sim.

Comments and problems are welcome.

How to unlock mobily 4G LTE router QDC in one attempt 2017

How to unlock mobily 4G LTE router QDC in one attempt 2016
Free Access to Technical Education #FATE

Crack it all by yourself, no need to go anywhere. I am not a tech at all, but i like to solve my problems and issues myself, usually i get succeeded.

Warning: Router will restart many times and you need at least 30min to finish all procedure. Never leave it in middle. Also this is purely my personal recommendation which we did for myself. Any damage happens to your router, We are not responsible at all for any thing. Do at your own risk. If you are ready to take risk, follow steps carefully.


Here is the method on how to unlock Mobily 4G LTE QDC router to unlock by yourself in one attempt

Step 1: Things we need

Its very simple, all you need is:

1. Mobily 4G

2. Remove if any sim card in router (V. Important, if u leave it there, problems can happen)
and

3. Following 3 files..

https://docs.google.com/file/d/0B1d3...it?usp=sharing

https://docs.google.com/file/d/0B1d3...it?usp=sharing

https://docs.google.com/file/d/0B1d3...it?usp=sharing

Download. Ok..Lets proceed to next step

Step 2: Go to 192.168.2.1

If you have any password, use that and enter the setup.

If you didn't change password since you bought it, default password it says

Leave Blank, and enter the SUBMIT button

Step 3: Next step is to check your Firmware version

Follow the picture and identify 

If your Firmware is as shown above 1.02.32 then proceed to next step 5
My recommendation even if your version is 1.02.32, still do step 4 and update your firmware, as the firmware thats already installed is from mobily.

If its 1.02.33 or 1.02.41 then proceed to step 4:

Step 4: Downgrade Firmware 

In order to avoid any damage / one time attempt in unlocking, follow this

The Zip file have two firmware

1.02.33    (mr7015al-zz_r0b_FW_1.02.33(20120618))

 and

1.02.32    (mr7015al-zz_r0b_FWN_1.02.32(20120330))


Click on the Firmware Update->than browse file 1.02.32    (mr7015al-zz_r0b_FWN_1.02.32(20120330))

then press UPDATE

As you can see now, version should be 1.02.32, if yes, proceed to next step


Step 5: Updating the LTE Module

Click on the LTE Module Upgrade -> than browse file LTE_20120321_1K5QCI_4036_M0.02

then simply press LTE UPDATE as shown below

This reboots the router again .Sometimes it will not respond even up to 2 minutes , let it finish flashing. Have patience!

Step 6: Click on the Adv.Setting


Vendor Profile select- no profile unlock – MCC/MNC: 0/00 - test

 SIM Lock - de select -

Allow Op List  ---  42003,42075  ---- with comma in between, picture below shows only one number, but i recommend to put both numbers.

Check Firmware info time-2-3 or 1-2

Change Firwareinfo URL to 0.00.00.00

(Its very Important step, otherwise you will have auto update by mobily and router will be locked again, and you have to unlock it again with whole process...)

and click Apply changes

Step 7: Click on the AT Command

> SIM Security -> Disable-> submit

as shown below in picture

Step 8: Optional but Recommended

If you are afraid, proceed to step 9

Now most people say that 1.02.32 is unstable firmware, i also agree with them, what i did to solve this.  I did an experiment and it was successful

I upgraded again my firmware from 1.02.32 to 1.02.33 by uploading this file to firmware

1.02.33    (mr7015al-zz_r0b_FW_1.02.33(20120618))

after this is done, proceed to step 9

Step 9: Click on the LTE/UMTS

Make changes for your network setting (like APN or dial no.) - then Apply change

You are good to go now, its unlocked and you need to set the APN settings only,

which you can find HERE

However if you don't like this to change APN settings every time you switch to a New service provider, do following changes...

Change 'always connected to Auto traffic triggered' as shown above in picture and step 2 is to leave APN 'blank' (means don't write anything in this line).

Apply changes

and then restart the router.. It should be working fine..

THE End: Enjoy

Hopefully you enjoyed this tutorial, and success in 1st attempt. If any problem happens, comments are welcome for the improvement and i may bring some new invention to solve that.. Keep visiting us for updates

athwbx.sys prevents windows 8 to 8.1 upgrade and also does not allows Windows 10 from upgrading to newer build?or becomes BLUE Dead Screen

This is a common problem now a days since new windows start to appear and most are stuck not able to solve it, as we are not all tech giants..
so here is my solution to this everyday issue

Actually I got the same problem in windows 8 then 8.1 and now windows 10,

How i solved it by myself, this is how,... im not a tech guy at all, just used common understanding of this freaking athwbx problem..

For windows 8 to 8.1

if u r upgrading from windows 8 to windows 8.1, immediately after install go to device manager in control panel, and disable wireless atheros driver.. so u can not connect anymore to wifi. thats fine for the moment.

Next go to windows update center and search for optional updates... there u will find an update to this wireless atheros driver.. now here is a trick also that made me restart n do this procedure 2 3 times at least.. turn off all other imp or not imp updates, tick only this driver update... ur internet connection should be fast enough to download 765kb of file in a blink of time and install it.. once u get it installed. there should be no problem anymore... and u can use wifi again on ur windows 8.1.. however sometime while its installing it gives blue screen again because it resists to be fixed.. u need to try again and again and im sure u will succeed as i did.

For Windows 10 Issues

ok now for new LOvely Windows 10..

we guys having same problem after upgrade of windows from 8.1 to 10

here is my own solution

I did this while i thought i got the same problem as windows 8.1.. 

it kept on showing blue screen and keep on restarting over 15min when i decided to step in and fix this crazy athwbx yet again.. ;)

i turned off laptop by power button and then i went to advanced options in windows 10.. NB when u restart windows 10 u will get these options automatically, no need to press any del or F10 buttons, thanks to tech guys in microsoft to make our life easier..

Go to advanced option and select safe mode option without networking...dont select networking otherwise again blue dead screen waits ahead..

In safe mode u need to do the same exercise as above, go to devise manager and disable ur atheros wireless driver, then again restart ur computer and connect internet by LAN and try to turn off windows update to manual.. then search for windows 10 updates manually and install them and most important step, go to again device manager and go to atheros driver, click right open it and go to driver tab, SIMPLY click on ROLL BACK TO OLD DRIVER, confirm yes and U r done...

enjoy ur wifi again on gorgeous windows 10..

hope it helped..

i posted this answer on Microsoft answer website, u can check other solutions there as well.