How to renew Vehicle Registration ISTIMARA online in Saudi Arabia, get it delivered at home/office.

Renewing Vehicle Registration License Online and Get it delivered at Home

Once upon a time, i was looking for a faster way to renew my vehicle Registration card, and I did reach to this method. What a wonderful method govt has provided here.
So, I decided to share it with you guys, hopefully you will get benefit out of it and save time...! Actually, you can get it delivered at home.

So, here is the method to update your Vehicle Registration (ISTIMARA) online right from your home.

FEE of Renewal of ISTIMARA:
MOST IMPORTANT: Go to your bank account online or to the nearest ATM and pay the fee for the Vehicle registration through Alien Control / Govt Payments. After you are done with that follow the following steps to renew your ISTIMARA.
Detail of the renewal fee can be found in the picture below, 
also in the link goo.gl/EQqYao

STEP 1: Go to website https://www.moi.gov.sa

STEP 2: You need to have absher account on moi website, if you dont have it, sign up to the New User on top right hand side of website as shown below.

STEP 3: After you are done with this, or if you already have an account, then go to login, It will show you like this.

STEP 4: Enter username and password or IQAMA ID and password that you created while registering to this site.

Enter the Image code

It will open another page like this and a verification code will be sent to your mobile number registered to this account. This is the security of website that no one else can open your account, even they know your password.

STEP 5: After you will enter the verification code, it will open a page like this.

STEP 6: Go to the Traffic tab, 8th line down and click 'VEHICLE SERVICES' as shown in the picture above

STEP 7: It will open a page showing your vehicle model, and date of expiry, everything (as shown in picture below)

 STEP 8: You can renew your ISTIMARA, only if less than 180 days are remaining. 

If you want to proceed then click on the 'RENEW VEHICLE REGISTRATION'

STEP 9: Once you are done, in the end you will get option to pick up card from Nearby MAROOR (traffic) office or you can choose the method of Deliver to Home. It will cost you 30 SR.

Make sure your address is correct, as the delivery can be delayed if you didn't put correct address.

However, if you want to pick your card yourself, here are the locations of Maroor offices in Riyadh, other cities offices you can locate in google map, very easy to find.

Here is the link

Hope it helps. eNjOy

How To unlock/update Mobily, Zain, STC router B593 all version all countries: Updated 2017

Updated method to unlock Mobily, Zain, Stc router B593 all version all countries

Specifications of this Router:

LTE TDD 2300/2600MHz
LTE FDD 800/1800/2600MHz
Wi-Fi b/g/n, up to 32 simultaneous devices
Firewall, VoIP, TR069 remote management
HTTP online upgrade, QoS, USB share, UPnP
IPv6, DLNA, fax, print, VPS, VLAN(option function)
OS: support Windows XP/Vista/7, Linux, Mac OS.

LTE CPE B593

Router full name HUAWEI B593, is the first LTE TDD wireless broadband router of the world, supports LTE TDD/FDD 800/1800/2300/2600MHz, up to 100Mmbs download speed and access to up to 32 WIFI devices that become an ideal home entertainment and information exchange hub, spupports multi-devices simultaneous high speed access, perfect for SOHO's and small businesses with its connectivity options

How to update software of router or to unlock it and use anywhere in world!!

Long wait is over now, here are all version software which will be required to update this router in any country by a simple method. After i received request from you people, i keep on trying and searching different methods, finally i cracked it by a simple method.

Most people said they can't unlock this router as the mobily software is updated to 103 or 104 version. I found a simple solution to that here, All you need is to follow my simple steps to update this router.
Remember, not to miss any single step and to identify right software for your version.(i will show you how to see which software you need)

Whats Needed?
You need:
1. Router
2. 30 minutes of your valuable time
3. That's it.
Yeah, the good part is, you don't have to open hardware of router. So far my method has not failed me over routers that i unlocked myself. No boot loop errors. Hopefully no damage will happen in the end & don't forget, we are here to help.

Disclaimer:
But before you start, any damage caused or happened to your router, We or our team is not responsible, do it on your own risk. 

Which Models are covered in B593?
All the models are covered in this tutorial. Remember, you don't need to pay for unlock codes or other difficult methods. I invented this method and succeeded in it.


STEPS to follow:
Here are the steps to follow:


Step 1: Turn on your router with/without sim, not the provider sim like mobily, use stc sim instead, connect to your router. (Download all files before starting your router without sim)

Step 2: Sign in IP address. It can be 2 IP address 192.168.1.1 or 192.168.100.1, check behind the router as shown in the picture below:

Step 3: Enter the password on the admin page, Default password is admin

Step 4: Go to System, then Device information.

Step 5: Very important step: Look for the 'Software version' which currently your router is running
It may look like this as shown in picture:

Step 6: Download the software that is higher version from the links below, remember the last 5 words are important: For example: SP032

Step 7: Download the B593 UPGRADE FILE

This file is the Jump-Start of this procedure, very important step, after downloading, don't extract file for now, as it is in .rar form.

B593 UPGRADE FILE

Step 8: Download the file from the links below:

V200R001C00SP032

V200R001C284SP033

V100R001C00SP052 

SP054

SP053

V100R001C07SP061

V100R001C55SP103
V100R001C55SP104
STEP: 9: Make your antivirus disabled, also turn off your firewall, you can make these changes by going into control panel of your PC and then follow next step.

STEP:10.. Start your router and go to the settings after login to the systems IP address. which is usually written on the back of the router, it may look like this
http://192.168.100.1 or 192.168.1.1, by default, device Password is 'admin', all of that is written on the back side of your router, no need to worry about that.

Now confirm, again, the version of router router software in the settings..

"Its very important to know the router software number esp the last 3 numbers as you have to choose the software above that number in order to succeed in the process."

Step: 11. On the right hand side you can see the reset button.

I want you to press all buttons together, the reset button with a pen and simultaneously pressing both buttons above and down to it as shown in picture below for 30 seconds at least

 Until you see all lights blinking and in the end only wps light will be blinking as shown

STEP:12. Start the B 593 upgrade software. Don't go to the ip address now.

STEP: 13. Select the 3rd option from drop down menu of the router (wireless if you are connected by wireless, or by LAN if you are connected by LAN) as shown in the picture below

STEP 14: Remember, choose the software either the higher one than its running or the same one if you are already running the latest software which is SP104.

STEP: 15. Select the software that you want to run, remember, the chosen software must be not the same software number that your router is running.

STEP: 16: After extraction, it shows the version in the software which should be the higher version of your actual software.

after extraction is complete, it will show you the version you are going to apply as shown in picture below

(note: sometimes the .rar version gives error, don't worry> extract the .rar files first then select from extracted files b593.trx file and it should show you the version in the B593 UPGRADE SOFTWARE as shown below. then click start button)

STEP: 17: Press start, Make sure that at least 18-20 packets have been run completely.

Make sure it runs all packets, in the mean time all lights of your router will keep on blinking as shown

STEP: 18: Go to the ip address now and it should show that upgrade is in process as shown in the picture below. Let it complete 100% and let it restart as shown in the pictures below.

Have a sip of tea, let it complete.

STEP: 19: Once all is done as explained, go to the ip address again.
It should show a totally new basic by default LTE B593 CPE page, login to the system and use the password 'admin' 

STEP: 20: Confirm the software version, its upgraded already. 

ENjOy & hit a like to my page or share if you want to.

Restart BOOT LOOP after attempting to unlock mobily 4G LTE router QDC

BOOT LOOP RESTART: HOW TO FIX IT

Question: i Unlocked for my Mobily 4G LTE Router , but it is not working,it rebooting continuously

This question is asked, here is the answer to it:

Answer: You are in BOOT LOOP, it means the device is not listening to any orders and keeps on trying to update itself which it fails and keeps restarting.. People say it can not be fixed.. No its not like that, there is a will, there is a way..

It can be easily fixed even by a guy who is non tech at all. Just follow the steps carefully and not to break anything. Again i want to emphasize that this will be at your own risk, any damage happens we are not responsible at all. Do at your own risk.
However to ease you, we did it at first attempt with zero to little knowledge about technology stuff ;)

STEP 1: Things you need:

1. Mobily QDC ROUTER
2. Screw driver (Star Shapped)
3. Time required 30 min to 1 hour

STEP 2:

Open the 2 screw at the back of router

Now to tell you that this cover has 4 hard rubber locks, you can just try to open them and you will hear click on each corner of router.

Separate back cover

Now you can see CHIP BOARD itself

It Also has 2 screws

Open them up as shown in picture

STEP 3:

Most important and careful step

Now identify GSM PORT, it has IMEI written over it.

Its rectangular shaped chip that has 2 screws at its end as shown in picture below

Open these 2 screws

Now carefully pull out GSM PORT, it should be separated easily with a gentle pull


STEP 4: Connect to power cable to router and start it

It should be working now

Keep GSM port separated and of course without sim in sim port

STEP 5: Follow the same steps to unlock device as shown in following link

How to unlock mobily 4G LTE router QDC in one attempt 2016

After you unlocked device with all steps in the above post without missing any point.
follow this step

STEP 6: Connect GSM Port

Connect GSM port to its place where it was as shown above

Put SIM card in sim port

Restart Router

Check for the connection , signal strength and SIM PORT LIGHT

If showing NO SIM

Confirm if the SIM PORT light is showing 'on' as shown in the above picture ...

If no, remove GSM PORT and insert it in again carefully and push a bit that its fixed inside well.

STEP 7: Confirmation

Check all system and internet is working before closing back router..

Everything should be working just fine..


THE END: ENJOY

Hopefully you solved your problem yourself with our blog, Keep visiting us. Any problem in the steps, comment down in comment box and leave your question or problem.. We will get back to you with solution as soon as possible. It would be better if you upload picture of the problem where you got stuck with. So we can help you from the same point, in order to not to waste your precious time..

APN settings for Saudi Arabia network providers: UNLOCKED 4G LTE routers QDC QUANTA

Settings:

Here are the settings, leave everything else as it is in picture,

Just you need to change APN according to your network sim

FOR STC:

APN:  jawalnet.com.sa

FOR ZAIN

APN: zain

FOR MOBILY itself ;) really you need this APN, ok here it is

APN: web2

 IF you don't like to change APN settings every time you use different network provider sim, simply leave this portion Blank and change 'Always Connected' to 'Auto Network triggered' and Apply Changes.

It should work fine without changing APN settings with every sim.

Comments and problems are welcome.

How to unlock mobily 4G LTE router QDC in one attempt 2017

How to unlock mobily 4G LTE router QDC in one attempt 2016
Free Access to Technical Education #FATE

Crack it all by yourself, no need to go anywhere. I am not a tech at all, but i like to solve my problems and issues myself, usually i get succeeded.

Warning: Router will restart many times and you need at least 30min to finish all procedure. Never leave it in middle. Also this is purely my personal recommendation which we did for myself. Any damage happens to your router, We are not responsible at all for any thing. Do at your own risk. If you are ready to take risk, follow steps carefully.


Here is the method on how to unlock Mobily 4G LTE QDC router to unlock by yourself in one attempt

Step 1: Things we need

Its very simple, all you need is:

1. Mobily 4G

2. Remove if any sim card in router (V. Important, if u leave it there, problems can happen)
and

3. Following 3 files..

https://docs.google.com/file/d/0B1d3...it?usp=sharing

https://docs.google.com/file/d/0B1d3...it?usp=sharing

https://docs.google.com/file/d/0B1d3...it?usp=sharing

Download. Ok..Lets proceed to next step

Step 2: Go to 192.168.2.1

If you have any password, use that and enter the setup.

If you didn't change password since you bought it, default password it says

Leave Blank, and enter the SUBMIT button

Step 3: Next step is to check your Firmware version

Follow the picture and identify 

If your Firmware is as shown above 1.02.32 then proceed to next step 5
My recommendation even if your version is 1.02.32, still do step 4 and update your firmware, as the firmware thats already installed is from mobily.

If its 1.02.33 or 1.02.41 then proceed to step 4:

Step 4: Downgrade Firmware 

In order to avoid any damage / one time attempt in unlocking, follow this

The Zip file have two firmware

1.02.33    (mr7015al-zz_r0b_FW_1.02.33(20120618))

 and

1.02.32    (mr7015al-zz_r0b_FWN_1.02.32(20120330))


Click on the Firmware Update->than browse file 1.02.32    (mr7015al-zz_r0b_FWN_1.02.32(20120330))

then press UPDATE

As you can see now, version should be 1.02.32, if yes, proceed to next step


Step 5: Updating the LTE Module

Click on the LTE Module Upgrade -> than browse file LTE_20120321_1K5QCI_4036_M0.02

then simply press LTE UPDATE as shown below

This reboots the router again .Sometimes it will not respond even up to 2 minutes , let it finish flashing. Have patience!

Step 6: Click on the Adv.Setting


Vendor Profile select- no profile unlock – MCC/MNC: 0/00 - test

 SIM Lock - de select -

Allow Op List  ---  42003,42075  ---- with comma in between, picture below shows only one number, but i recommend to put both numbers.

Check Firmware info time-2-3 or 1-2

Change Firwareinfo URL to 0.00.00.00

(Its very Important step, otherwise you will have auto update by mobily and router will be locked again, and you have to unlock it again with whole process...)

and click Apply changes

Step 7: Click on the AT Command

> SIM Security -> Disable-> submit

as shown below in picture

Step 8: Optional but Recommended

If you are afraid, proceed to step 9

Now most people say that 1.02.32 is unstable firmware, i also agree with them, what i did to solve this.  I did an experiment and it was successful

I upgraded again my firmware from 1.02.32 to 1.02.33 by uploading this file to firmware

1.02.33    (mr7015al-zz_r0b_FW_1.02.33(20120618))

after this is done, proceed to step 9

Step 9: Click on the LTE/UMTS

Make changes for your network setting (like APN or dial no.) - then Apply change

You are good to go now, its unlocked and you need to set the APN settings only,

which you can find HERE

However if you don't like this to change APN settings every time you switch to a New service provider, do following changes...

Change 'always connected to Auto traffic triggered' as shown above in picture and step 2 is to leave APN 'blank' (means don't write anything in this line).

Apply changes

and then restart the router.. It should be working fine..

THE End: Enjoy

Hopefully you enjoyed this tutorial, and success in 1st attempt. If any problem happens, comments are welcome for the improvement and i may bring some new invention to solve that.. Keep visiting us for updates

athwbx.sys prevents windows 8 to 8.1 upgrade and also does not allows Windows 10 from upgrading to newer build?or becomes BLUE Dead Screen

This is a common problem now a days since new windows start to appear and most are stuck not able to solve it, as we are not all tech giants..
so here is my solution to this everyday issue

Actually I got the same problem in windows 8 then 8.1 and now windows 10,

How i solved it by myself, this is how,... im not a tech guy at all, just used common understanding of this freaking athwbx problem..

For windows 8 to 8.1

if u r upgrading from windows 8 to windows 8.1, immediately after install go to device manager in control panel, and disable wireless atheros driver.. so u can not connect anymore to wifi. thats fine for the moment.

Next go to windows update center and search for optional updates... there u will find an update to this wireless atheros driver.. now here is a trick also that made me restart n do this procedure 2 3 times at least.. turn off all other imp or not imp updates, tick only this driver update... ur internet connection should be fast enough to download 765kb of file in a blink of time and install it.. once u get it installed. there should be no problem anymore... and u can use wifi again on ur windows 8.1.. however sometime while its installing it gives blue screen again because it resists to be fixed.. u need to try again and again and im sure u will succeed as i did.

For Windows 10 Issues

ok now for new LOvely Windows 10..

we guys having same problem after upgrade of windows from 8.1 to 10

here is my own solution

I did this while i thought i got the same problem as windows 8.1.. 

it kept on showing blue screen and keep on restarting over 15min when i decided to step in and fix this crazy athwbx yet again.. ;)

i turned off laptop by power button and then i went to advanced options in windows 10.. NB when u restart windows 10 u will get these options automatically, no need to press any del or F10 buttons, thanks to tech guys in microsoft to make our life easier..

Go to advanced option and select safe mode option without networking...dont select networking otherwise again blue dead screen waits ahead..

In safe mode u need to do the same exercise as above, go to devise manager and disable ur atheros wireless driver, then again restart ur computer and connect internet by LAN and try to turn off windows update to manual.. then search for windows 10 updates manually and install them and most important step, go to again device manager and go to atheros driver, click right open it and go to driver tab, SIMPLY click on ROLL BACK TO OLD DRIVER, confirm yes and U r done...

enjoy ur wifi again on gorgeous windows 10..

hope it helped..

i posted this answer on Microsoft answer website, u can check other solutions there as well.